August 1, 1997
Marc E. Cook
Pilots — and, in particular, aircraft owners — often complain about the high cost of flying. The plaintive wails customarily decry lofty fuel prices, exorbitant parts bills, or avaricious A&P mechanics, and yet it's a certainty that the enterprising owner can find ways to make flying a bit more merciful to his wallet. (Indeed, one of the best ways to reduce the cost of flying is to do it more often. Strictly from a bookkeeping standpoint, the more you fly your own airplane, the less expensive it is on a per-hour basis. But as a practical matter, a frequently flown airplane will be less costly to maintain because it will require fewer unscheduled trips to the shop.)
By far one of the most effective ways to cut maintenance bills is to become involved. There are, of course, different levels of involvement, and each has its own rewards and shortcomings. At the least, every aircraft owner should be maintenance aware; that is, to understand how his or her airplane normally operates and to be able to discern performance and maintenance anomalies. Further up the scale of involvement is the owner who assists in routine inspections and maintenance. (A subset of this group includes those owners who perform the allowed preventive maintenance items spelled out in Federal Aviation Regulation Part 43, Appendix A. These are tasks that a pilot may perform without direct supervision of an A&P.) And, finally, there are those hardy souls who actually perform all of the maintenance duties, using the appropriately hired wrenches to oversee the work and sign off the logbooks. Somewhere in this spectrum is bound to be a zone of comfort for you. (Indeed, a sampling of AOPA members revealed that nearly two-thirds are inclined to become involved with the maintenance.)
Perhaps the worst way to conduct routine maintenance is to drop off the airplane at the repair facility, throw the receptionist the keys, and say, "Call me when it's done." You are just about guaranteeing that the maladies you may have noticed during otherwise routine flights will not be fixed, and that a selection of items that might safely be deferred to a better time (such as during an engine overhaul, major paint job, or interior rework) will be conscientiously and expensively repaired by well-meaning wrenches.
Prior to sending in the airplane for major maintenance such as the annual inspection, you should take the time to seek out squawks that you may not have noticed. Do all the lights work? The radios? How about the autopilot in all of its modes? Try every system in the airplane — including the emergency gear extension — and confirm that the stall- and gear-warning horns work properly. The more sleuthing you do ahead of time, the less digging around the mechanics will need to do; by necessity this is digging you will ultimately bankroll.
Take the time to carefully peruse the airplane's logbooks. Are there any outstanding airworthiness directives? Any of them recurring? Is the pitot-static/transponder check due? Are any of the engine accessories — magnetos, fuel pump, alternator, starter, exhaust system — subject to new ADs? Are all of the ship's repair and major-alteration papers in order?
Embarking upon a collaborative relationship with an individual mechanic or shop can be a delicate dance. Try to find someone who seems willing to teach, and, naturally, be ready to receive an education yourself. Outline and agree upon exactly what you will be doing during the inspection and how many of the physical tasks the mechanic is willing to let you accomplish. Even if you're pretty handy with a wrench, respect the A&P's experience by leaving your pride and boastfulness at home. There's no better way to sour a relationship than to tell the A&P how to do his job. It may be your airplane, but it's his shop — and his signature that designates the airplane as airworthy.
Now that you've done your homework — and found a willing mechanic who will let you do some or most of the work — you're ready to tackle the dirty work. Bring grubby clothes or coveralls and a small assortment of common hand tools. Good mechanics are loathe to lend tools — most would rather share toothbrushes than Snap-Ons. Have an electric screwdriver with a breakaway clutch at the ready — batteries charged and several screwdriver bits ready to go. The adjustable clutch ensures that you don't inadvertently over-torque the access-panel screws at the end of the job. If you do, the next annual will be pure agony.
As you might have guessed, the loathsome job of removing some or all of the access panels for the inspection will fall into your proud-airplane-owner hands. It's a nasty chore, but you'll get used to it. (Amazing how many owners decide that the cost of something like the smooth belly kit for Mooneys — which cuts the screw count by a factor of 10 — is much more reasonable after an assisted annual.) Plan to bring a couple of boxes of plastic sandwich bags to hold the hardware for each panel; mark each bag to identify the contents or tape it to its mating panel. Depending upon the condition of the hardware, you might take this opportunity to replace the screws with stainless-steel equivalents; they don't corrode and will probably make the next inspection easier.
Follow your spanner-boss through on some of the major inspections like the differential-compression check, control system lubrication and integrity, and engine compartment inspection. You will probably be issued the assignment of removing, cleaning, and gapping the spark plugs. Pay particular attention to the swinging of the gear, if you own a retractable. Watch a Cessna 210's monkey motion and you might well reconsider dropping the gear at the maximum-allowable speed for every arrival.
Part of any thorough annual involves removing some or all of the interior furnishings; again, this time-consuming job — one often best left to contortionists — will be your jewel. As always, take your time and ask questions if any part of the job isn't perfectly obvious.
As you develop your relationship with the wrench-in-charge, tasks and responsibilities tossed your way will blossom. For many owners, the attending mechanic is just a reference tool and an extra set of eyes and hands. (He is, of course, plenty handy when it comes time to sign off the logbooks.) Indeed, with the supervision of the appropriate person — A&P for most tasks, and one with an inspection authorization for the annual — you can legally do just about everything in the manual. The limits are really set by your abilities and available time.
Yet another advantage of working closely with the inspecting A&P involves the decision-making process. At many points in the annual, for example, the mechanic must decide whether a marginal item should be repaired or replaced on the spot, or deferred to the next annual or inspection period. You have the advantage of knowing what you'd like to do with the airplane long-term; the A&P doesn't. So, if you have a cylinder trending downward in compression, for example, but you know that in 6 months or a year you plan on upgrading the powerplant, you can save yourself a possible partial top overhaul. You can also confer with your aide on whether a new or overhauled part is best for your needs; again, your knowledge of the airplane's past and your plans for its future will help tremendously.
The other side of this involvement coin is that you cannot be an intractable penny-pincher. After all, the inspecting technician has to put his name and signature in the logbook that the airplane is airworthy. Your job in this relationship is not to nickel-and-dime him to death. He will not smile upon cost-cutting tactics that might compromise safety.
With time, you should be able to develop a relationship with a mechanic or shop that will both provide the service institution with welcome business and give you peace of mind that the inspections have been performed properly and at a reasonable cost.
Becoming one with your airplane's maintenance needs requires some research. So it only makes sense that the savvy owner will have a comprehensive library of source material. What do you need?
E-mail the author at email@example.com.
Aircraft Power and Fuel,
As the cold weather chills AOPA’s Headquarters in Frederick, many of us are inside generating new resources for flying clubs.
In my house, every Friday night is “Movie Night.” While the movies are rarely educational (I don’t think I learned anything from the Lego Movie), we look forward to the weekly opportunity to spend time together. Why not use the same concept for your Flying Club (with the addition of education, of course)?
The Aircraft Spotlight feature looks at an airplane type and evaluates it across six areas of particular interest to flying clubs and their members: Operating Cost, Maintenance, Insurability, Training, Cross-Country, and Fun Factor.
VOLUNTEER AT AN AOPA FLY-IN NEAR YOU!
SHARE YOUR PASSION. VOLUNTEER AT AN AOPA FLY-IN. CLICK TO LEARN MORE >>>
VOLUNTEER LOCALLY AT AOPA FLY-IN! CLICK TO LEARN MORE >>>
BE A PART OF THE FLY-IN VOLUNTEER CREW! CLICK TO LEARN MORE >>>