June 1, 2009
By Dave Hirschman
How would you like to cut your hangar rent in half? Or add a second airplane to your fleet without increasing your hangar costs?
Tom Crone already owned and flew a Grumman AA1B when he came across a beautifully restored Piper J-3 Cub that he very much wanted to buy. The question was where to put it.
Crone didn’t want to leave either airplane outside, subject to the Mid-Atlantic heat, cold, wind, and rain. And a second hangar was unobtainable—both in terms of ongoing costs ($400 a month) and a years-long waiting list.
Crone’s answer was to buy a hangar lift that allowed him to keep both airplanes, protected, inside a single T-hangar.
In an ongoing effort to squeeze more flying out of our aviation dollars, AOPA is seeking your tips on frugal flying. Have you found creative ways to operate your aircraft more efficiently? Better manage maintenance, training, hangar, tie-down, or insurance costs? Or buy aviation-related goods in bulk or at lower prices? E-mail the author at [email protected]
In three years, Crone said he’s already avoided enough additional expenses to cover the $9,000 cost of the hydraulic lift he purchased new from the manufacturer. The lift can accommodate nose- or tailwheel airplanes, and the Cub usually goes up in the winter and the Grumman in the summer. It takes about three minutes to fully raise or lower the lift.
Crone said the lift also comes in handy for maintenance. “It’s great when you’re doing wheel or brake work,” he said. “You can clean and wax the belly of the airplane, and the bottom of the wings—areas that are hard to reach when the airplane is on the ground.”
The lift has jack points that allow for hoisting an airplane and retracting the gear without crawling under the airplane. Crone said he has no concerns about the lift failing. And neither, apparently, does his insurance carrier. It costs no more to insure an aircraft kept in a hangar with a lift than without one.
“I looked at the machine drawings before I bought the lift, and I have no concerns about its structural strength,” Crone said. “Its drive shaft is extremely durable. It’s not going to fail.”
Marty Kononel, owner of Aero-Lift, a company that has manufactured hangar lifts since 2001, said there has never been a structural failure of any of his company’s products. Aero-Lift is based in Tucson, Arizona, and the lifts are manufactured near Philadelphia.
The retail price for a new lift is about $11,000, and lifts are sometimes available on the used market. Used lifts typically retain about 75 percent of their value.
Aero-Lifts have a maximum capacity of 2,500 pounds, so they are suitable for most single-engine airplanes up to a BE-36 Bonanza or Cirrus SR22. The lifts themselves weigh about 2,700 pounds, and they work best in hangars with a ceiling at least 16 feet above the ground.
About 400 Aero-Lifts have been sold in the last eight years. “They’re popular among pilots who want to split hangar costs, or consolidate in one hangar,” Kononel said. “They’re also used extensively by owners of large, gang hangars as a way to increase revenue without adding more physical space.”
E-mail the author at [email protected]
AOPA Pilot Editor at Large Dave Hirschman joined AOPA in 2008. He has an airline transport pilot certificate and instrument and multiengine flight instructor certificates. Dave flies vintage, historical, and Experimental airplanes and specializes in tailwheel and aerobatic instruction.
Cost to Operate,
Any time preventive or repair maintenance is performed on an aircraft, there's a risk of introducing...
The Department of Justice has approved the sale to Signature Flight Support of Landmark Aviation, if...
A group chaired by AOPA has been tasked with developing new certification standards, handbooks, and ...
VOLUNTEER AT AN AOPA FLY-IN NEAR YOU!
SHARE YOUR PASSION. VOLUNTEER AT AN AOPA FLY-IN. CLICK TO LEARN MORE >>>
VOLUNTEER LOCALLY AT AOPA FLY-IN! CLICK TO LEARN MORE >>>
BE A PART OF THE FLY-IN VOLUNTEER CREW! CLICK TO LEARN MORE >>>