July 8, 2013
By Jeff Simon
In the last article, we reviewed good practices for propeller care and built up a little more respect for the importance of keeping your prop in top shape. In this installment, we’ll talk more about preventive propeller maintenance and how to make minor repairs.
Preventive maintenance begins with regular, careful inspections of the propeller. Even small areas of damage such as nicks and rock dings can represent stress points that can lead to cracks or corrosion. It pays to be vigilant and attend to small areas of damage before they become big ones.
Making minor repairs to propeller blades is not a particularly challenging task, but technique is important, and it’s not something that owners can do themselves. FAA Advisory Circular 43.13-1B is an excellent reference for understanding blade repairs.
Patience and careful planning are key. It’s fairly easy to remove aluminum from a propeller blade and impossible to put it back. This is especially important when you realize that every propeller blade has dimensional limits that restrict the amount of metal that can be removed during repairs before the propeller becomes unairworthy.
So, proceed with caution and follow these basic steps:
Blades can be maintained in the field, but maintenance on constant-speed propeller hubs is far more complex. Lubrication or charging with nitrogen (on certain hubs) are the only field-serviceable tasks on most constant-speed hubs. Lubrication of the propeller hub is very important because it keeps the mechanism operating smoothly and changing the grease will help eliminate contaminants that can cause corrosion. However, it must be done according to the manufacturer’s exact instructions and only with the specified grease. Anything beyond these tasks should only be performed by a propeller maintenance facility.
Regular oil changes are also very important in aircraft with constant-speed props. Since engine oil provides the power source for controlling propeller pitch, ensuring that the oil is clean will reduce the chance that the propeller and governor will have problems caused by sludge or water contamination. Also, be sure to leave constant-speed propellers in a horizontal or, in the case of three blades, in a “Y” position to minimize any water collection on the hub.
Wooden propellers are truly works of art and should be treated as such. They should be inspected regularly for damage and delamination. Pay particular attention to the metal tips, looking for loose screws, rivets, or solder. The varnish coating serves a critical role in protecting the propeller from moisture damage and should be carefully maintained. If the propeller is removed for any reason, the bolt holes and hub bore should be inspected for elongation and damage. Then, the holes should be treated with a moisture preventive such as asphalt varnish.
The compressible nature of wood requires that the torque on the propeller bolts be checked regularly. If moisture enters the wood, it can swell and then become loose after drying out. Typically, propeller torque should be checked 25 hours after installation and every 50 hours thereafter.
Finally, regardless of the type of propeller that you have, perform a propeller tracking check. This is a fairly simple procedure that any owner can do. Ensure that the mags are off, then remove one spark plug from each cylinder so that the propeller can be easily rotated. Next, rotate one of the blades so that it is pointing down and place a wooden block under the blade tip, marking the exact spot that the tip passes over on the block. Finally, rotate the propeller, checking the other blades to ensure that they track within one-sixteenth of an inch of the mark. Any variation beyond one-sixteenth of an inch is cause for concern. It may be caused by a bent blade and should be inspected and repaired by a propeller maintenance facility.
Jeff Simon is an A&P mechanic, pilot, and aircraft owner. He has spent the last 14 years promoting owner-assisted aircraft maintenance as a columnist for several major aviation publications and through his how-to DVD series: The Educated Owner. Jeff is also the creator of SocialFlight, the free mobile app and website that maps more than 5,000 aviation events. Free apps available for iPhone, iPad, and Android, and on the Web at www.SocialFlight.com.
FAA Information and Services,
Aircraft Power and Fuel,
Nextant Aerospace, adding a remanufactured King Air to its remanufactured Hawker 400 offering, says the King Air (Nextant G90XT) will fly early next year.
The FAA has issued an airworthiness directive to require continued repetitive inspections of aft fuselage structures for cracks on some models of Bellanca airplanes.
Williams International says customers in its Total Assurance Program for engine maintenance can extend all FJ44 models to an engine overhaul interval of 5,000 hours.
VOLUNTEER AT AN AOPA FLY-IN NEAR YOU!
SHARE YOUR PASSION. VOLUNTEER AT AN AOPA FLY-IN. CLICK TO LEARN MORE >>>
VOLUNTEER LOCALLY AT AOPA FLY-IN! CLICK TO LEARN MORE >>>
BE A PART OF THE FLY-IN VOLUNTEER CREW! CLICK TO LEARN MORE >>>